3D PRINTER UNDER 200$ Smackdown!

3D PRINTER UNDER 200$ Smackdown! Ender 3 Best Buy in 2019 ?

If you are new to 3D printing, and are unsure of what to ask, try to include the following in your posts as a minimum:

  • Your budget, set at a numeric amount. Saying “cheap,” or “money is not a problem” is not an answer people can do much with. 3D printers can cost $100, they can cost $10,000,000, and anywhere in between. A rough idea of what you’re looking for is essential to figuring out anything else.
  • Your country of residence.
  • If you are willing to build the printer from a kit, and what your level of experience is with electronic maintenance and construction if so.
  • What you wish to do with the printer.
  • Any extenuating circumstances that would restrict you from using machines that would otherwise fit your needs (limited space for the printer, enclosure requirement, must be purchased through educational intermediary, etc).

While this is by no means an exhaustive list of what can be included in your posts, these questions should help paint enough of a picture to get started. Don’t be afraid to ask more questions, and never worry about asking too many. The people posting in this thread are here because they want to give advice, and any questions you have answered may be useful to others later on, when they read through this thread looking for answers of their own. Everyone here was new once, so chances are whoever is replying to you has a good idea of how you feel currently.

Additionally, a quick word on print quality: Most FDM/FFF (that is, filament based) printers are capable of approximately the same tolerances and print appearance, as the biggest limiting factor is in the nature of extruded plastic. Asking if a machine has “good prints,” or saying “I don’t expect the best quality for $xxx” isn’t actually relevant for the most part with regards to these machines. Should you need additional detail and higher tolerances, you may want to explore SLA, DLP, and other photoresin options, as those do offer an increase in overall quality.

As always, if you’re a newcomer to this community, welcome. If you’re a regular, welcome back.Or if in case if u have any doubt regarding 3d printing u can use email to contact us !

I have divided the printers into category like depending upon price and most important total vale for you money !

Under 200$

Ender 3

No doubt Creality did a really impresssive launch of this in March after massive success of CR Series Not just the quality put into this but proper research and development they took the initiative and made it possible that a affordable just out of the box easy to assemble 3D Printer was made !
Similar in many regards to its big brother, the Ender 3 is the smaller, wallet friendly option with a price tag just under $200.

While there are a lot of 3D Printers to browse at this cost section, none of them managed to check all of the boxes until now. Customers regularly needed to forfeit one element in return for another, for example, construct volume for fabricate quality or the other way around. Never again is this the case with the Ender 3, which figures out how to give a protected, well fabricated machine that is equipped for creating extensive, radiant prints appropriate out of the case.

It’s not a perfect 3D printer by any stretch of the imagination, but it’s probably the closest we will see at this price for quite some time.

The Creality Ender 3 is a unprecedented 3D printer when you take the sub-$200 tag into consideration.

There are variety of options that create the Creality Ender 3 one amongst the foremost popular machines presently on the market. it has a build volume of 220 x 220 x 250mm, a BuildTak-like heated build plate, power recovery mode and a good filament pathway that makes it easier to print with versatile materials. These are attributes that are tough to search out in even costlier printers…

As for printing performance, the Creality Ender 3 exceeded our initial expectations. I experimented with PLA, PETG, ABS, flexible and exotic filaments, and whereas there have been some adhesion and warp problems with ABS, along with some wood filament difficulties, i have managed to print with success with all of the materials at the end of the day.

The 3D printer is simple to assemble and–although it needs manual calibration–the enlarged bed leveling knobs make the process convenient. Once calibration is perfected (it would possibly take a few attempts), the Creality Ender 3 ultimately became indistinguishable from printers that are nearer to the $1000 range.

The most obtrusive issue presented by the Creality Ender 3 is that the uneven base, which causes a small wobble to the whole 3D printer. i were ready to solve this by putting a wedge underneath one corner, but still, this primary downside was positively a cause for concern as stability could be a vital half to a high quality 3D printer.

Otherwise, we didn’t have several different qualms with the Creality Ender 3. there have been some bed adhesion problems with certain materials, like ABS, however adding some adhesive answer to the build plate solved this rather quickly.

The Creality Ender 3 is a wonderful choice for beginners or manufacturers on a budget. whereas this 3D printer will have its flaws, the affordability makes it a worthy investment. in contrast to different budget choices in this price range, just like the Anet A8, the Creality Ender 3 is ready for high-quality 3D printing right out of the box. On prime of that, the growing community encompassing this 3D printer has led to additional and additional upgrades.

Creality additionally offers an “Ender 3 Pro”, that has a detachable magnetic heated bed and enhancements to the y-axis to achieve a better print quality.

There are certainly better 3D printers available on the market, however none appear to fuse quality and affordable quite like the Creality Ender 3. it might need a small amount of tweaking and patience to realize the perfect print quality, however the high potential that this budget 3D printer offers makes well definitely worth the battle.

Tech Specs

Here’s a brief overview of the specifications for Creality Ender 3:

  • Technology: FDM
  • Print Area: 220 x 220 x 250mm
  • Nozzle: 0.4mm
  • Filament: 1.75mm PLA, ABS, TPU
  • Max. Print Speed: 200mm/s
  • Max. Layer Resolution: 0.1mm
  • Print Precision: +/-0.1mm
  • Heated Bed: Yes
  • Connectivity: SD Card, USB
  • LCD Screen: Yes

Software

Before we wrap up our first impressions review of the Creality Ender 3, we wanted to touch on the topic of software, particularly regarding slicer settings. After scouring through Google to find pre-defined slicer settings for Ultimaker Cura, there wasn’t any printer profile to upload into the slicer software.

Additionally, the USB provided with the Creality Ender 3 included a download for Cura, but only for Windows. Therefore, as the reviewer was operating on a Mac OS, there was no way to download the slicing software from the resources provided by the manufacturer. An annoyance? Sort of. But it’s also the kind of problem we found an easy solution for.

Thankfully, the Creality Ender 3 has been gaining enough of a presence among the 3D printing community, that we found pretty promising slicer settings on YouTube from user KNOWLEDGE INFINITY. After inputting the entire list of print settings, which can be found in the video description, we set off to experiment with the recommended data to see how well it worked.

Some important notes to keep in mind when adding the Creality Ender 3 as a custom FDM 3D printer to Cura. First and foremost, make sure you change the nozzle diameter in the main menu from 2.85mm (the default number) to 1.75mm. This small step is easy to skip over, and doing so will result in an under-extruded and overall disappointing print.

We found that, for the most part, these Cura settings worked exceptionally well. But don’t be afraid to experiment a bit until you find the most satisfying results for your own printing goals.

Where to Buy

Currently, the best price for the Creality Ender 3 can be found on Banggood and Gearbest. If you’re interested in picking this 3D printer up for yourself, check out the link below.

Buy From BANGGOOD.COM
Buy From GEARBEST.COM

You Might Also Like
Leave a Reply